About   Contact    |    



What makes the bathroom faucet drip ?

I’m wondering what’s causing the water to start falling from the faucet in the kitchen these days. So I did some research to find out what caused the water to fall from the faucet. please noted that article is subitable for all the faucet, such the bathroom faucet , 3 piece bathroom faucet and dual handle deck mounted faucet.
Why does the faucet fall? The most common cause of faucets falling out of the spout is worn washers. And there is a high possibility that the O-ring where water drops fall around the handle is damaged. What causes
faucets to drip depends on different types of faucets. So let’s take a look at some of the causes of faucets dripping.

Causes of faucet dripping

A dripping faucet can be cumbersome as well as very costly if unattended. Here are a number of causes of a faucet dripping:

  • Worn Washer
  • Damaged O-ring
  • Corroded Valve Seat
  • Wear Cartridge
  • Irregular Water Pressure

What makes the bathroom faucet drip ? - Blog - 1

Worn Washer

This is the most common cause of faucets falling. Here the water droplets come out of the mouth. It also comes from a compression faucet. There is a washer on the base of the faucet.The faucets in the 3-piece bathroom have double handles, the right handle adjusts for cold water and the left handle adjusts for hot water.

Damaged O-ring

If drips are under or near the handle, damage to the oring is most likely the cause. It is the disk attached to the cartridge that holds the handle of the faucet. Also, this problem is unique to cartridge faucets.

Corroded Valve Seat

The valve seat connects the faucet to the spout. As the valve seat corrodes, the faucet begins to fall around and under the steering wheel. This phenomenon often occurs when sediment accumulates. Occasionally clean and precautionary measures are taken.

 Wear Cartridge

Wear cartridges can cause the faucet to drip. The cartridge’s inlet and outlet seals can wear out over time due to the build-up of deposits. Also, this type of leak only occurs with cartridge faucets. I am using a VIGA kitchen single hole faucet ceramic cartridge. It is healthy and environmentally friendly. The diameter of the faucet hole is 35 mm. You can install it on youshelf someday.

Irregular Water Pressure

In rare cases, fluctuating water pressure can cause the faucet to fall. Also, these water pressure irregularities can cause much greater problems. Therefore, if the problem persists, it is advisable to notify your local water supplier.

What makes the bathroom faucet drip ? - Blog - 2

Fixing a Dripping Faucet

I recommend a professional plumber for the job. It’s not that complicated though, so you can do it yourself. After all, that can’t be fun either.
Your faucet goes to one of the 4 types of faucets there. They are compressed ceramic disc cartridges and ball faucets. Each has its own replacement parts and repair methods.
Before starting, shut off the water supply to the faucet. You can almost find it under the sink. Then make sure you have sealed the drain in the sink. If the sink does not have a plug, you can use cloth or floor covering. This is to prevent the parts from flowing into the drain. Now you’re ready to start.

Compression Faucet

Compression faucets usually have two handles. One for regular use and one for cold. Also, the handle is usually twisted to open and close the flow of water. However, the other three types of faucets all have one handle or rotating arm for controlling both hot and cold water.
First, remove each handle. In some cases it may be necessary to loosen the screw from raising the handle. Remove the nut using the following wrench. Below that is the system in Oring and in the Oring seat washer. Because seat washers are rubber, they may wear out over time. If the water is dripping from the spout of your faucet. This may be the cause. However, if water drops around the handle fall, the O-ring needs to be replaced.

Ceramic-disc Faucet

The first step is to remove the handle and remove it to remove the flange cup. Then loosen and remove the disc cylinder screws. You can identify it by looking at the bottom with multiple neoprene stickers.
Take the deleted disc to a hardware store for an accurate replacement. Then place the ceramic disc exactly in the ejected position. After that, restore the handle and reassemble. It is important to choose water slowly. Too strong a run of water may damage the ceramic disc.

Cartridge Faucet

Tilt the handle back to loosen and remove the screw. Sometimes you have to remove the decorative cap first. Then remove the retaining clips as needed. Generally made of plastic, it locks the cartridge in place. It can be removed using forceps. Then pull the cartridge upright. This is generally the position when the water is fully open.
Now remove the mouth and store it separately to find Orings. Use a utility knife to cut the old O-ring. Before installing a new Orings, make sure it is coated with plumber grease. This is the end of reassembling the handle after replacing the O-ring.

Ball Faucet

The ball faucet has many parts that need replacement. And some of these parts also need to be specialized. Therefore, it is recommended to purchase a replacement kit.

These are inexpensive and contain all the necessary tools. And they are available at most home repair shops. These kits will help you replace the faucet cam assembly rather than the entire faucet. Remove the
handle and start putting it aside. Next, use pliers to remove the cap and collar. After that, use the tool included in the replacement kit to unscrew the faucet cam. Then, remove the cam, washer and ball. Next, remove the suction seal and spring using radio pliers.

Cut pastand remove Orings. Don’t forget to lubricate the plumber before doing a fresh install. Install new springs, valve seats and cam washers included in the replacement kit. Then reassemble all parts and finally reassemble the handle. Don’t forget that the assembly order is the reverse of the disassembly.

Maintaining Your Faucet

Faucets generally require little maintenance. This is especially true for faucets made by major manufacturers. Nevertheless, it can sometimes give a good luster.
Use a window glass cleaner or soap to make the faucet glossy on a soft cloth. you can rub Rubbing the faucet with a soap pad with solid bristles may damage the finish and should not be used. Before using the cleaner, read the manual and check whether it is suitable for your faucet.

To clean the matte finish faucet, you can use an aerosol or liquid furniture polish. It also gives furniture shine a nice uniform appearance and protects it from fingerprints. This is due to the silicone oil contained in the varnish.

Replacemet the faucet

If you are in the downstream area, you may already be facing that challenge. It can also clog faucets and drains, although it can have a high mineral content. Vinegar can be used to remove deposits of these minerals. To explain in detail, soak the parts inside the faucet in vinegar for at least 4 hours. You can then use a toothbrush to break the deposit.

And, the faucet may require minor repairs. A common indication that the faucet needs some repair is at startup when the water falls. In most cases, minor repairs are generally associated with replacing springs and washers. As mentioned above, there are four types of faucets, each with its own repair method.
In conclusion there is a type of sealed faucet. Therefore, it cannot be deleted. In this situation, the only option is to replace the entire device. Make sure the model can be removed during replacement.

What makes the bathroom faucet drip ? - Blog - 3

VIGA, founded in 2008, has more than 12 years experience in producing and exporting. there are 60 series products, and CUPC, TISI, CE, IOS 9001,BSCI, etc.

One hour reach jiangmen port, that what we can offer the best price and high quality faucet to our customer.

If you want to get our E-catalog, please email: info@vigafaucet.com.

Website: www.vigafaucet.com/ www.viga.cc



Live Chat
Leave a message